User Manual
This is the users manual that
is delivered with your ProExtender™.
The manual is available in these
languages :
- English
- Danish
- Deutch
- Spanish
- Japanese
INTRODUCTION
The ProExtender™ was designed and
developed in Denmark by Danamedic Aps. The purpose of the extender is to
lengthen the penis by means of traction. The ProExtender™
can be used as a gentle mono-theurapeutic device. The use of the ProExtender™
does not require medical supervision.
The mechanism of the device is based
on the principle of traction, a method which simulates the human body’s
natural reaction to the application of physical force. Tissue cells react
by multiplying and the tissue gradually expands, a principle utilized by
various indigenous tribes for multiple doubling of the size of earlobes
and lips.
The ProExtender™
has been tested on patients who have all obtained lengthening
of the penis after using the device in accordance with instructions.
The lengthening is permanent and does not entail a narrowing of the circumference
of the penis.
The test subjects achieved an average
lengthening of the erected penis of 2.8 cm (24 per cent) after a treatment
period of 3-4 months. The treatment does not affect urination, sexual prowess
or the power of reproduc-tion. Lengthening can only be obtained by daily
usage of the device and the effect correlates with the number of hours
of usage. The above mentioned results were obtained after 12 hours’ daily
treatment over a period of 3 months.
DESCRIPTION OF THE VARIOUS COMPONENTS
AND INSTRUCTION FOR ASSEMBLAGE
The Extender consists of a basal
plastic ring (1) with a recess for the urethra (2). The ring is fastened
around the root of the penis. Two metal bars, one with a right-handed thread
(3), the other with a left-handed thread (4) are attached to the basal
ring. Inside each bar, hidden in a tube, is a spring contrivance (5). At
the distal end the two bars are attached to a plastic support (6) with
two holes, through which the ends of a silicone tube are passed.
The components 1-5 are preassembled
on delivery. Depending on the size of the penis either the short or the
long extension bars are mounted by means of the round spanners provided
(See fig. 3, page 9). The additional extension bars are required for later
usage as lengthening of the penis occurs. The plastic support is mounted
by introducing the ends of the bars (5) into the two big holes of the support.
The support is then pressed towards the basal ring (1). The springs are
thus pressed home. Pressure should be exerted until a snap or a click indicates
that the support is firmly secured to the bars.
INSTRUCTIONS FOR MOUNTING
The device is mounted by fastening
the basal ring (1) around the root of the penis, so that the two metal
bars (2) run parallel with the penis, one on each side, and the head of
the penis rests in the bowl-shaped support (3). By passing the two ends
of the silicone tube through the holes in the plastic support (4) a loop
is made through which the head of the penis is introduced. Before fastening
of the penis the plastic support should be pressed towards the body so
that the two springs press home. The silicone tube is fastened around the
penis head by pulling the ends of the tube (5) on the reverse side of the
support. In men who have not been circumcised the silicone tube is fitted
just below the glans with the foreskin in place. The ends are pressed into
the two notches (6) to secure the fastening of the penis head. Additional
pieces of metal bar (7) may be added as required by means of the two keys
(8).
PROTECTION PAD ACCESSORY TO THE
ProExtender™.
In rare cases initial soreness can
be experienced from using the Extender. Such soreness is usually caused
by initial excess of force, which should not exeed 6-900 gram of traction
for 4-8 hours daily during the first 2-3 weeks. The force of the traction
should then be increased to 900-1200 grams, and the treatment period to
8-12 hours daily.
To relieve such occasional soreness,
the enclosed Protection Pad can be used in the following way:
- Expand the Protection Pad slowly.
- Fit it behind the penis glans,
and allow it to contract to a snug fit.
- Mount the extra long silicone
tube as usual.
The Protection Pad can be washed
in lukewarm water, and new pads can be purchased at your local Extender
dealer or from this site.
INSTRUCTIONS FOR ADJUSTMENT
When the device has been fitted
the force of trac-tion can be adjusted by turning the two thumb-screws
(1) in an inward direction. The actual force exerted can be read on the
hexagonal pistons (2) and the force of traction can be varied from 600
to 900, 1200 or 1500 g (see fig. 4). Each marking on the piston equals
a traction force of 300 g. Thus, at the exertion of maximum force (1500
g) only one marking is visible on the piston. A force of 600-900 g is recommended
for the first 2-3 weeks and during that period the Extender should not
be worn for more than 4-5 hours a day. From then on the force may be increased
to 900-1200 g and to 12 hours daily usage of the device. The Extender should
be worn approximately 12 hours a day for a total period of 3-6 months.
INSTRUCTIONS FOR USE AND DISMOUNTING
OF THE EXTENDER
During use of the Extender
the penis can be held at any position except sideways. In a pair of loose-fitting
trousers the device is inconspicuous. It can be worn at night but may become
detached during uneasy sleep or during a nightly erection. Accidental detachment
merely requires re-mounting of the device.
The device is dismounted by loosening
the silicone tube from the ventral side of the support. The
Extender can then be detached. The thumbscrews are screwed home in
an outward direction towards the basal ring. When not in use the Extender
can be left assembled or it can be disassembled and placed in the box as
required.
MATERIALS USED
1.
Silicone type: WMQ, USP 21-4, PA/HP/exp3/(82)57/1984.
Owing to its chemical composition
Silicone rubber is temperature resistant, weather resistant and re-sistant
to wear and tear. It is proof against exposure to temperatures ranging
from -65¢ª C to +210¢ª C.
2 + 4.
Plastic parts: POM (Hostaform),
C 2521 G
Proof against temperatures ranging
from -20¢ª C to +80¢ªC.
3.
Brass: CuZnS9Pb3 - W.no. 2.0401.
Nitin coating: Nitin is an intermetallic
composition, combining the properties of nickel and tin, which is produced
by electrolytic depositing. Clinical trials have demonstrated that Nitin
coatings, despite their contents of 35% nickel, do not seem to precipitate
any reaction in nickel allergics.
5.
Stainless steel springs: Din 17224
- W.no. 4310
CLEANING
The ProExtender™ should be cleaned
daily with soap and water.
A chlorhexidine alcohol solution
of 0.5% can be used for disinfection.
ENVIROMENTAL ASPECTS
The ProExtender™
is delivered in packaging indispensable to shipment of the device. Only
environment friendly and reclycable materials are used.
Wooden box:
Made of mahogany, harvested from
African or North American trees, cut down every ten years as part of routine
forestry maintenance.
Glue and varnish:
Water based.
Corrugated paper:
Contains no less than 45% recycled
material. Can be recycled.
Plastic bags:
PVC-free. Only carbon dioxide and
water are liberated on incineration.
The brochure:
The paper is made of chlorine free
bleached cellulose.
Printing ink does not contain heavy
metals.
Foam rubber:
Made of PUR foam. Does not emit agents
which act on the skin.
http://www.proextender.com
Page 1
| Page 2 | Page
3 | Page 4
